Pre-test validation: Airline Transport Pilot Helicopter
What the examiner checks before your ATP helicopter checkride can start: the 61.161 experience, the cross-country hours that count and the ones that only look like they count, SIC and PIC time, the knowledge test, and a helicopter that can fly the instrument tasks.
The short version
Before the oral begins, the examiner must verify that you meet every eligibility and aeronautical experience requirement for the ATP certificate (8900.1 Volume 5, Chapter 2, Section 18). If one item is missing, the test cannot start, and that is not a failure. It means rescheduling once the missing item is fixed. ATP applicants are experienced pilots, so the problem is rarely a missing hour. It is usually hours logged under the wrong definition.
- You are eligible: 23 years old, English, good moral character, a commercial pilot certificate with an instrument rating, a passed ATP helicopter knowledge test (an expired one is still good if you fly for a Part 135 operator and have completed its PIC training or checking program, 61.39(c)), and at least a third-class medical
- Your logbook shows the 61.161 experience: 1,200 hours total, 500 cross-country, 100 night (15 in helicopters), 200 in helicopters (75 as PIC or as SIC performing the duties of PIC), and 75 instrument (50 in flight, 25 of those in helicopters as PIC or SIC)
- Your cross-country hours meet the rotorcraft definition: every flight counted toward the 500 has a landing more than 25 nm straight-line from where it started. Part 135 A-to-B time that never went that far does not count
- You can act as PIC on the test: a current flight review or a qualifying check, and in a Robinson the SFAR 73 requirements
- The helicopter can fly every PTS task, including two precision approaches, two different nonprecision approaches, holding and two missed approaches, and its records prove it is airworthy
When the rules are unclear. A few parts of the ATP experience requirements are not settled by the regulation or by any FAA interpretation, and this guide does not take a side on those. Plan that part of your experience the conservative way, so the time counts under any reading, and send your logbook to ATACS before you book. An examiner cannot accept time that is open to question, and an eligibility problem cannot be fixed after the test.
Which path are you on?
| Path | Who it fits | Experience rule |
|---|---|---|
| Part 61, initial ATP helicopter | Commercial pilot with an instrument rating earning a first ATP certificate | 61.161. Airline Transport Pilot Helicopter knowledge test. Practical test to the ATP helicopter PTS. |
| Part 135 operator check | Pilot employed by a Part 135 certificate holder | 61.157(f)(1)(ii): a 135.293(a)(2) and (b) competency check plus a 135.297 PIC instrument proficiency check, given by an FAA inspector or an authorized check airman or evaluator, satisfies the flight proficiency requirement. The 61.161 experience still applies. See section 6. |
| Part 141 or 142 graduate | Graduate of an approved ATP helicopter course | 61.71(a), with the graduation certificate |
| Military pilots | Military helicopter pilots | 61.153(d)(2) accepts the 61.73 military qualification in place of the commercial and instrument ratings. The ATP itself still needs the knowledge test, the 61.161 experience and the practical test. See section 6. |
The restricted privileges ATP (61.160) is for airplanes only. There is no restricted ATP helicopter certificate.
1. Eligibility (61.153 and 61.39)
- Age. At least 23 (61.153(a)(1)). You may take the knowledge test earlier, as long as you will be 23 before the test report expires (61.35(a)(3)(iii)(A)).
- English. You must read, speak, write and understand English (61.153(b)). The examiner checks this against the FAA Aviation English Language Standard. If it is in question before the test, the test does not start and you are referred to the Flight Standards office.
- Good moral character (61.153(c)). The examiner is required to ask whether you have been convicted of a felony. A yes answer goes to the Flight Standards office before the test (8900.1 paragraph 5-704C).
- A commercial pilot certificate with an instrument rating (61.153(d)(1)), or a military qualification under 61.73 (61.153(d)(2)), or a foreign commercial license with an instrument rating or a foreign ATP license with instrument privileges, issued by an ICAO state with no geographic limits (61.153(d)(3)). Bring the plastic card, and for a foreign license, the FAA verification letter.
- Knowledge test. The Airline Transport Pilot Helicopter test, passed within the 24 calendar months before the month you complete the practical test (61.39(a)(1)(i)), unless the Part 135 exception below applies. The 60-month validity applies only to the multiengine airplane ATP after the certification training program. A Notice of Disapproval or Letter of Discontinuance does not extend it.
- Part 135 pilots: the knowledge test does not expire. An expired ATP helicopter test report is accepted if, at the time of the practical test, you fly as a flightcrew member for a Part 125 or 135 certificate holder and have completed that operator’s approved PIC training or checking program, or fly in U.S. military air transport operations and have completed the PIC qualification program (61.39(c), Kientzy 2009). Bring a letter on company letterhead that confirms your employment and eligibility (8900.1 paragraph 5-713E9). Use a paper application. IACRA will not accept an expired knowledge test report, so this application is made on a paper FAA Form 8710-1 instead of in IACRA. Tell ATACS when you request the test.
- No certification training program. The ATP CTP (61.156) is required only for the multiengine airplane ATP.
- A medical. At least a third-class medical certificate for the test, if it is flown in an aircraft (61.39(a)(4)). To exercise the PIC privileges of the ATP certificate afterward, you need a first-class medical (61.23(a)(1)(i)).
- Identification. A current government photo ID. The name must match your pilot certificate, knowledge test report and IACRA application exactly.
- The IACRA application. Mark ATP. If you are using an expired knowledge test under the Part 135 exception, the application is on paper instead (see above). The Instructor Action section does not need to be signed for an ATP, unless you are retesting after a failure (8900.1 paragraph 5-709C, 61.49). Section III, Record of Pilot Time, must match your logbook.
2. Aeronautical experience (61.161)
The ATP helicopter numbers are not hard to reach for a working pilot. What stops ATP tests is time that was logged correctly for a job but does not meet the Part 61 definition for a certificate: cross-country time above all, then SIC time and instrument time.
The requirements
| 61.161(a) requirement | Minimum | What counts and what to watch |
|---|---|---|
| Total time as a pilot | 1,200 hours | Time in any category counts (Shea 1990, M. Shea 1991). Airplane, powered-lift and other time all go toward the total. |
| Cross-country time | 500 hours | Need not be in helicopters (8900.1 ATP helicopter job aid), but every flight must meet the rotorcraft definition in 61.1: a landing more than 25 nm straight-line from the original point of departure. Part 135 “A to B” time that never went that far does not count. Details below. |
| Night flight time | 100 hours, 15 in helicopters | Night is the time between the end of evening civil twilight and the beginning of morning civil twilight (14 CFR 1.1). Night vision goggle flights at night count as night time. |
| Helicopter flight time | 200 hours | Flight time in a helicopter. Device time does not count here: flight time is time in an aircraft (14 CFR 1.1). |
| Helicopter PIC or SIC performing the duties of PIC | 75 of the 200 | PIC time logged under 61.51(e), or SIC time performing the duties of PIC under the supervision of the PIC, in any combination (61.161(a)(3)). The SIC time must be time you could log as SIC under 61.51(f) (Duncan 2012). Details below. |
| Instrument time | 75 hours | Actual or simulated instrument conditions, flying solely by reference to instruments (61.51(g)(1)). Up to 25 hours may be in a full flight simulator or flight training device that represents a rotorcraft, or up to 50 hours in a Part 142 course (61.161(b)). |
| Instrument time in flight | 50 of the 75 | In an aircraft, not a device. |
| Instrument time in helicopters, as PIC or SIC | 25 of the 50 | In a helicopter, as PIC, or as SIC performing the duties of PIC under the supervision of the PIC, or a combination (61.161(a)(4)). |
The requirements overlap. A night IFR flight in a helicopter to a hospital 40 nm away counts toward the total, cross-country, night, helicopter, PIC and instrument hours at once, as far as each part of the flight meets each definition.
One cross-country column, two definitions
This is the most common ATP problem ATACS sees, and it usually starts years before the test.
Part 61 has more than one definition of cross-country time (14 CFR 61.1):
- The general definition (paragraph (i)): a flight with a landing at a point other than the point of departure, navigating by pilotage, dead reckoning or navigation systems. A 6 nm hop from base to a hospital pad meets it.
- The rotorcraft definition (paragraph (v)), for the aeronautical experience for any pilot certificate with a rotorcraft category rating, including the ATP: a flight that includes a landing at a point more than 25 nm straight-line from the original point of departure.
Where it goes wrong. The Part 135 PIC minimums ask for cross-country time too: 100 hours for VFR (135.243(b)(2)) and 500 hours for IFR (135.243(c)(2)). Those minimums are not experience for a certificate or rating, so the 25 nm rule in paragraph (v) does not govern them, and many Part 135, HEMS and tour pilots log every flight with a landing somewhere else as cross-country. That is fine for the job. The problem comes later: the logbook has one cross-country column with 1,500 hours in it, and nobody can tell which of those flights landed more than 25 nm from where they started. Only those count toward the 500 hours for the ATP.
- Keep two columns. If you log under the general definition for Part 135, add a second column, for example “XC 61.1 (25 nm+),” and log a flight there only when it had a landing more than 25 nm from its original departure point. Electronic logbooks let you add a custom field for this.
- Write the route in the remarks or route column. The examiner verifies cross-country time from the entries. Identifiers or place names for each landing make that possible years later.
- If you only have one column, go back through the entries before you apply and total only the qualifying flights. Operator trip records are accepted as reliable records of flight experience (8900.1 Volume 5, Chapter 1, Section 8). Do not enter the combined column total in Section III of the IACRA application as your cross-country time.
- ATACS reviews the entries. On an ATP test, the examiner works through the logbook to confirm the 500 hours. If your cross-country column mixes both kinds of flights, send the logbook before you book so the review happens before test day, not during it.
Measuring a cross-country flight
The Chief Counsel’s interpretations on the cross-country definition apply to the ATP the same as to any other certificate:
- Every flight counted toward the 500 hours must meet the definition (Keller 2009). A flight with a long leg but no landing more than 25 nm from the start does not count.
- Distance is measured straight-line from the original point of departure, not from the last stop, and no single leg has to be 25 nm (Sisk 2008, Van Zanen 2009, Glenn 2009). A multi-stop medical or utility flight counts once one of its landings is more than 25 nm from where the flight started.
- You decide what a “flight” is when you log it, not afterward (Van Zanen 2009). Splitting or combining entries later to make them qualify does not work.
- An overflight is not a landing. Flying a patrol or survey 40 nm out and back without landing is not rotorcraft cross-country time.
- Leave a real margin. Apps measure from different reference points. A landing an app shows at 25.1 nm is not proof. Use landing points that are reasonably over the distance by any measurement.
- Log the whole flight time. Cross-country time is logged as flight time under 14 CFR 1.1, from when the helicopter moves under its own power for the purpose of flight until it comes to rest after landing (Grannis, June 2016). Rotors turning on the ground before the helicopter moves, or after it is parked, is not flight time (Lloyd 2007).
- One pilot gets the cross-country experience. Two pilots who trade the controls on a trip to build time cannot both credit it as cross-country time toward a certificate (Hilliard 2009), and a safety pilot does not log cross-country time (Glenn 2009).
Cross-country examples, drawn out
Each diagram is to scale. The inner ring is 25 nm from the departure point and the outer ring is 50 nm.
Counts toward the helicopter ATP
Does not count: landing inside 25 nm
Counts: measured from the original departure
Does not count: no landing beyond 25 nm
PIC and SIC time
- PIC time is logged under 61.51(e): as the sole manipulator of a helicopter you are rated for, as the sole occupant, as the PIC of an aircraft or operation that requires more than one pilot, or as an authorized instructor giving training (61.51(e)(1) and (3)). Autopilot time still counts (Murphy 2015).
- SIC time is logged only when the helicopter’s type certificate, or the regulations for the flight, require more than one pilot (61.51(f)). Examples: a helicopter certificated for two pilots, a Part 135 passenger flight under IFR without an autopilot authorization (135.101 and 135.105), or a safety pilot during simulated instrument flight (91.109(c)). A company policy that puts a second pilot in the left seat does not make that pilot a required crewmember, and that time is not SIC time (Cato 2014). In a helicopter that needs only one pilot, only the rated pilot on the controls logs PIC, and the other pilot logs no SIC (Pfaff 2014). A Part 135 operator that elects before an IFR flight to use a second pilot in place of the autopilot makes that pilot a required SIC (Nichols 2009).
- SIC performing the duties of PIC. 61.161(a)(3) and (a)(4) let you count SIC time during which you performed the duties of PIC under the supervision of the PIC. It is still logged as SIC time; it is not PIC time unless you also meet 61.51(e) (Duncan 2012). Ask the PIC to note in your logbook which flights you flew as the pilot performing the duties of PIC, so the examiner can see it.
- A rated SIC who is the sole manipulator may log PIC for that time (61.51(e)(1)(i), Murphy 2015). A type rating limited to “SIC privileges only” does not allow logging PIC in that type (Morgan 2013, an S-61 question; Counsil 2012, Morris 2012).
- Part 135 SIC professional development program time logged under 61.159(c) counts toward the 1,200 total and the cross-country, night and instrument hours, but not toward the helicopter-specific requirements (61.161(c)). Bring the Part 135 training records that 61.39(a)(3)(i) requires.
- SIC time in public aircraft operations logged under 61.51(f)(4) counts only in a large aircraft, a turbojet, or an aircraft that holds or held a type certificate requiring a second pilot.
- The ICAO limitation. Using either kind of time puts “Holder does not meet the pilot in command aeronautical experience requirements of ICAO” on your ATP certificate (61.161(d)). For public aircraft time, it applies only if the aircraft was not type certificated for two pilots (61.51(f)(4)(ii)). The limitation comes off later, when you show the 61.161 experience without that time (61.161(e)). The examiner will ask whether any of your SIC time was in public aircraft operations (8900.1 paragraph 5-713E5).
Instrument time
- Instrument time is time flying solely by reference to instruments (61.51(g)(1)). Being in instrument conditions, or flying on goggles, is not instrument time by itself. Log only the time you operated the helicopter solely by reference to instruments.
- Simulated instrument time in flight needs a safety pilot in the other control seat (91.109(c)). The safety pilot does not log instrument time for it, and does not log cross-country time (Glenn 2009).
- An instructor giving instrument training in actual conditions may log instrument time (61.51(g)(2), R. Levy 2008).
- Hood time with an instructor counts as PIC for the 25 helicopter hours if you are rated in the helicopter and are the sole manipulator (61.51(e)(1)(i)). An instrument rating is not needed to log PIC as sole manipulator (Speranza 2009).
Simulators and training devices
- Full flight simulator or flight training device: up to 25 hours of simulated instrument time toward the 75 instrument hours, in a device that represents a rotorcraft (61.161(b)(1) and (2)). Up to 50 hours if the training was in an approved course at a Part 142 training center (61.161(b)(3)).
- An instructor must be present to observe the device time and sign your logbook or training record with the content of the session (61.51(g)(4)).
- Aviation training devices (ATDs). 61.161(b) names only full flight simulators and flight training devices. ATD time counts only for the uses listed in the device’s letter of authorization (Holmes 2014). Check the LOA for what it allows toward the ATP, and ask ATACS before counting any ATD time toward the 75 hours.
- Device time is not flight time (14 CFR 1.1). It never meets a requirement that says “in helicopters” or “in flight”: the 200 helicopter hours, the 15 helicopter night hours, the 50 instrument hours in flight or the 25 helicopter instrument hours.
Logging and records
- A logbook is any reliable record the FAA can read (Murphy 2008). Paper, electronic and operator records all work. Lost logbooks can be reconstructed with a signed statement of flight time, supported by aircraft logbooks, operator records, rental receipts, and copies of earlier 8710-1 applications and medical applications (8900.1 Volume 5, Chapter 1, Section 8).
- Military records are accepted if they meet 61.73(h), but they do not always show what Part 61 asks for, especially cross-country distances (8900.1 paragraph 5-708A). Bring flight records that show the departure and landing points for the time you count as cross-country.
- Total each column before you fill in IACRA. The examiner compares Section III of the application with the logbook, and with what you counted as qualifying cross-country, night, instrument and helicopter PIC time.
- The checkride itself can be logged as PIC (Murphy 2009).
3. Training records
- No specific training is required by Part 61 for the ATP helicopter certificate, and no instructor endorsement is required for the practical test (61.39(f)(3)), unless the test helicopter requires a type rating (section 4).
- Knowledge areas. The oral covers the 61.155(c) areas that apply to helicopters: regulations for ATP privileges and flight operations, meteorology, weather and NOTAM systems, weather charts and reports, windshear and microbursts, IFR navigation, ATC procedures, weight and balance and performance, aerodynamics, human factors, aeronautical decision making, and crew resource management.
- Knowledge test deficiencies. There is no required endorsement for the missed subject areas, but the examiner tests them on the oral. Review them.
- Part 125 or 135 crewmembers testing under that operator’s program bring the training records or a statement from a check airman showing the ground and flight training are complete (8900.1 Volume 5, Chapter 3, Section 1, Figure 5-109).
4. Endorsements to check
The ATP helicopter certificate needs very few endorsements. Below they are listed by regulation. Your instructor writes them. Sample wording is in AC 61-65K (November 2025), which has no ATP helicopter template.
Instructors can print the endorsements that may apply, such as a retest, the flight review and the SFAR 73 endorsements, on Avery 5163 labels with the free ATACS helicopter endorsement generator.
For the ATP certificate
- No endorsement is required to take the ATP helicopter practical test in a helicopter that does not require a type rating (61.39(f)(3)).
- Retest after a failure: 61.49, from the instructor who gave the additional training. The instructor also signs the Instructor Action section of the IACRA application (8900.1 paragraph 5-713C2).
- Type rating, if the test helicopter requires one: 61.157(b)(1) and (2), training on the areas of operation and an endorsement from an authorized instructor, or 61.157(c), a training record showing you completed a Part 121 or 135 certificate holder’s approved training program for that type. See section 5.
To act as pilot in command on the test
The examiner is not the PIC (61.47(b)), so you are.
- Flight review: 61.56(a) and (c), within the previous 24 calendar months. A proficiency check or practical test for a certificate, rating or operating privilege in that period takes its place (61.56(d)), and a Part 121 or 135 check counts (Lamb 2016).
- Instrument currency under 61.57(c) is needed only if you act as PIC under IFR on the test. It is not needed for instrument tasks flown under a view-limiting device in visual conditions.
- Type rating: to act as PIC of a helicopter that requires a type rating, you need the type rating, or you must meet the eligibility requirements for it (61.39(a)(3)(ii)).
Robinson R44 and R66
- R44, SFAR 73 PIC endorsement: SFAR 73 paragraph 2(b)(2)(ii), unless you have 200 helicopter hours with at least 50 in the R44 (up to 25 of the 50 may be R22 time). Many ATP applicants have the 200 hours but not the 50 in the R44. For pilots training now, the training for the endorsement must include minimum rate of descent and maximum glide autorotations (Amendment 61-154, July 2024). Endorsements received before that change are not affected.
- The 12 calendar month review: without the 200 and 50 hours, you may not act as PIC of the R44 beginning 12 calendar months after the PIC endorsement until you complete an SFAR 73 flight review in the R44 (paragraph 2(b)(2)(iii)).
- Flight review in the model: a 61.56 flight review counts for the R44 only if it was taken in an R44 and covered the SFAR 73 subjects (paragraph 2(c)).
- The R66 is not covered by SFAR 73. The normal 61.56 flight review applies.
5. The helicopter and its records
The applicant provides the helicopter (61.45). It must be airworthy, it must have the equipment for every area of operation on the test, and it must not have operating limitations that prohibit any of them (61.45(b)(1)). The PTS requires the test to be flown in actual or simulated instrument conditions, so the instrument equipment matters as much as the airworthiness records.
What the PTS instrument tasks require of the helicopter
- Two precision approaches to the decision altitude, using the helicopter’s navigation equipment for centerline and vertical guidance: an ILS, or a GPS approach with vertical guidance to a DA, such as LPV. At least one is flown without the autopilot from no later than the final approach fix. One should be flown with backup or partial panel instrumentation.
- Two different nonprecision approaches. At least one includes a course reversal, such as a procedure turn or a hold in lieu. One is flown from the initial approach fix without the autopilot and without radar vectors. One is flown with backup or partial panel instrumentation.
- Two missed approaches, one from a precision approach and one flying the published missed approach procedure.
- Holding, an instrument takeoff, an instrument departure and an instrument arrival.
- An installed IFR-approved GPS must be used for the approach tasks if the helicopter has one (PTS Area of Operation V). Know the box, its database and its approach modes.
- A view-limiting device that blocks your view outside without blocking the examiner’s. You furnish it (61.45(d)(2)).
Helicopters limited to VFR
Most R44s and R66s are approved by their flight manuals for VFR only. That does not keep them off the ATP checkride. The FAA Chief Counsel has said that an aircraft does not need to be IFR certified to operate on an IFR flight plan, as long as it stays in visual meteorological conditions (Theriault 2010, a helicopter question). The VFR-only limitation prohibits flight in instrument conditions, not instrument procedures. ATACS accepts a helicopter limited to VFR for the ATP practical test when:
- It has the IFR equipment in 91.205(d), installed and working, and the navigation equipment to fly every approach on the test, including two precision approaches. The Instrument guide lists the 91.205(d) items.
- The IFR inspections are current: altimeter, static system and encoder (91.411) and transponder (91.413) within 24 calendar months, a VOR check within 30 days if you use VOR under IFR (91.171), and a current navigation database for the GPS.
- The whole test stays in visual conditions. The flight manual limitation still applies (91.9(a)). The instrument tasks are flown under a view-limiting device, and if you file IFR, you do not accept a clearance into instrument conditions. Pick the day by the weather.
- If you file IFR, you are the PIC under IFR, so you need instrument currency under 61.57(c).
Tell ATACS the make, model and avionics when you request the test so the equipment can be confirmed before test day.
Other aircraft points
- Single-engine or multiengine. In a single-engine helicopter, the powerplant failure tasks are flown as autorotations, and one precision approach is flown manually. In a multiengine helicopter, you fly the one-engine-inoperative tasks, including a manually controlled precision approach with a simulated powerplant failure.
- A helicopter that requires a type rating. If you take the test in one, the test also covers the type rating, and you must hold or be eligible for that type rating (61.39(a)(3)(ii), 61.157(b)). If the instrument part of a type rating test is flown with two pilots, the type rating can carry an “SIC Required” limitation (Gibbons 2012, an AW139 question). Any helicopter type ratings already on your certificate move up to the ATP level when you pass (61.157(d)).
- Simulators. A full flight simulator or flight training device can be used for parts of the test only within an approved Part 141 or 142 course, or a Part 121 or 135 program for that operator’s pilots (61.64(a)(2)). Tests with ATACS are normally flown in the helicopter.
- Airworthiness and registration certificates aboard, the rotorcraft flight manual, and current weight and balance.
- Inspections: annual, and the 100-hour if the helicopter is used for flight instruction for hire and furnished by the person giving the instruction (91.409(b)). If the applicant furnishes the helicopter, the 100-hour does not apply on that basis (Colvin 2011, Walters 2018). Operator helicopters on an approved inspection program bring that program’s records.
- Airworthiness directives, including recurring ADs and any component retirement times in the limitations.
- Robinson helicopters: Robinson publishes a consolidated list of U.S. airworthiness directives for the R22, R44 and R66, including their engines and appliances. Find it on the Robinson publications page under More Material, U.S. Airworthiness Directives. It is the manufacturer’s summary, so confirm anything newer in the FAA’s Dynamic Regulatory System.
- Transponder tested within 24 calendar months if it will be used (91.413), and ADS-B Out where required. If you plan to file IFR, the altimeter and static system check (91.411) must also be current.
- Inoperative equipment must be handled under 91.213 or the operator’s MEL and must not be needed for any task on the test.
6. Other paths
- Part 135 operator checks. A pilot employed by a Part 135 certificate holder can meet the flight proficiency requirement with both a competency check under 135.293(a)(2) and (b) and a PIC instrument proficiency check under 135.297, given by an FAA inspector, or by an aircrew program designee or training center evaluator authorized for that operator (61.157(f)). Only the approach types in the operator’s operations specifications are required (Kane 2011). Eligibility, the knowledge test and the 61.161 experience still apply.
- Part 141 or 142 graduates present the graduation certificate. 61.71(a) applies only if you pass the practical test within 60 days after graduation.
- Military pilots. 61.153(d)(2) lets a military pilot who meets 61.73 apply without first holding the commercial and instrument ratings. The ATP itself still needs the knowledge test, the 61.161 experience from military records that meet 61.73(h), and the practical test. See the military competency guide.
Where pre-test checks usually fail
- Part 135 “A to B” time counted toward the 500 hours of cross-country, with no way to show which flights had a landing more than 25 nm from the start.
- Cross-country flights at or barely over 25 nm, or flights whose only long leg was between two points inside 25 nm of the departure point.
- SIC time logged when two pilots were not required by the type certificate or the regulations for the flight, counted toward the 75 hours.
- Instrument time that was not flown solely by reference to instruments, or more than 25 hours of simulator or training device time.
- Fewer than 15 night hours in helicopters, or fewer than 25 instrument hours in helicopters as PIC or SIC.
- Knowledge test past 24 calendar months without a current Part 135 PIC training or checking program to extend it, or without the company letter.
- A VFR-only helicopter missing 91.205(d) equipment, or with the 91.411 or 91.413 checks out of date.
- A helicopter that cannot fly two precision approaches, or whose GPS database is out of date for the approaches on the test.
- Expired flight review, or in an R44, an SFAR 73 review that is past 12 calendar months or was not in the R44.
- IACRA totals that do not match the logbook, especially a cross-country total copied from a mixed column.
Working with ATACS
Send a request with your eligibility path, the helicopter make, model and avionics, and your preferred dates. See the ATP Helicopter checkride page for what to bring and what happens on test day.
Sources
- 14 CFR Part 61: 61.1 (cross-country time), 61.23, 61.35, 61.39, 61.45, 61.47, 61.49, 61.51, 61.56, 61.57, 61.64, 61.71, 61.73, 61.153, 61.155, 61.157, 61.159(c), 61.160, 61.161, 61.167, and SFAR 73
- 14 CFR 1.1 (flight time, night)
- 14 CFR Part 91: 91.9, 91.109, 91.171, 91.205, 91.213, 91.409, 91.411, 91.413
- 14 CFR Part 135: 135.101, 135.105, 135.243, 135.293, 135.297
- FAA-S-8081-20A, Airline Transport Pilot and Aircraft Type Rating Practical Test Standards for Rotorcraft Category Helicopter Rating (November 2023)
- FAA Order 8900.1, Volume 5, Chapter 2, Section 18, Conduct an Airline Transport Pilot Certification, Including Additional Category/Class Ratings; Volume 5, Chapter 3, Section 1, Figure 5-109, ATP helicopter applicant qualifications job aid; Volume 5, Chapter 1, Section 8, Pilot Logbooks
- Robinson Helicopter Company publications, U.S. Airworthiness Directives list
- AC 61-65K, Certification: Pilots and Flight and Ground Instructors
- FAA Chief Counsel legal interpretations, in the FAA’s Dynamic Regulatory System: Cato (2014), Colvin (2011), Counsil (2012), Duncan (2012), Gibbons (2012), Glenn (2009), Grannis (June 2016), Hilliard (2009), Holmes (2014), Kane (2011), Keller (2009), Kientzy (2009), Lamb (2016), Lloyd (2007), Morgan (2013), Morris (2012), Murphy (2008), Murphy (2009), Murphy (2015), Nichols (2009), Pfaff (2014), R. Levy (2008), Shea (1990), M. Shea (1991), Sisk (2008), Speranza (2009), Theriault (2010), Van Zanen (2009), Walters (2018). All are searchable in the DRS legal interpretations collection.